Total Pipe
Robotic Solutions
Services / 04 — Map

3D Pipe Mapping

XYZ route, depth and alignment recorded as the camera travels — for the laterals, service lines and building stacks where the as-builts are missing, wrong or unverifiable. A mapped pipe before anyone opens the ground.

XYZ coordinatesDepth & alignmentGIS-ready exportVertical stacks
The problem

You cannot design a repair for a pipe you cannot locate.

Most inspection scopes stop at condition — what the pipe looks like. They do not tell you where it goes. On private-side laterals, building service lines and vertical stacks that is usually the missing half, and it is the half that decides where a crew digs.

The record drawings are frequently the problem. They were drawn before three rounds of tenant improvements, they show a line that was rerouted in 1994, or they do not exist at all. Nobody finds out until a crew is standing over a cut that missed.

Our push cameras record the route as the head travels, forward or reverse, and build a three-dimensional map of the pipe as they go — XYZ coordinates, width, length and elevation, rendered as a site plan in real time. We run it as a push system and behind a lateral launch, so the route is captured whether we enter from the cleanout or from the main.

It happens on the same pass as the inspection. There is no separate mobilization and no separate invoice for it.

WHAT IT PRODUCES

A mapped pipe, not a guess

  • 3D pipe route with XYZ coordinates
  • Real-time site plan during the inspection
  • Width, length and elevation of the run
  • Coordinates captured travelling in either direction
  • Vertical mapping of building stacks and risers
  • Export into your drawing set or GIS
What you get back

A route with coordinates on it, not an arrow on a drawing.

Two bends and seventy feet of difference between what the record drawing claims and where the pipe actually is. That gap is the whole reason this service exists — and it is only visible once somebody measures it.

PLAN VIEW — ROUTE AS RECORDED BUILDING MAIN P1 BEND 1 BEND 2 TIE-IN WHAT THE AS-BUILT SHOWS SECTION — DEPTH AND FALL GRADE 2.1 ft 3.0 ft 5.4 ft 7.8 ft at the tie-in

Illustrative. Every point on the route carries an XYZ coordinate and a depth, captured as the camera head travels — which is what turns “the lateral leaves the building and goes somewhere” into a position a crew can dig to.

Where it earns its cost

The scopes that turn on knowing where the pipe is.

01

Before the excavator arrives

Locating an unmarked lateral or service line before excavation. One mapped route against one exploratory dig that misses — the arithmetic is not close.

02

Building stacks and risers

Confirming stack and branch routing in a commercial or high-rise building where the as-builts are missing or were never updated. Vertical mapping to 164 ft.

03

Point repair design

Establishing depth and alignment so a repair is designed against a real position rather than an assumed one, and the permit reflects what is actually there.

04

I&I and private-side programs

Documenting private-side laterals for an inflow and infiltration program, where the route is as much a part of the record as the defects on it.

05

Correcting the as-built

Updating a drawing set that has drifted from reality, so the next contractor and the next capital cycle work from something true.

06

Campus and portfolio records

Bases, campuses and property portfolios where nobody has a complete picture of the buried system and every project starts with the same rediscovery.

How it is captured

The sensor is in the camera head, not on a separate trip.

A sensor package in the push head records position continuously as the camera advances. There is no survey crew, no locator sweep over the ground and no second visit — the route and the condition record come off the same deployment.

3" – 12"

Diameter range

Laterals, service lines, building branches and stacks — the small-diameter assets where routing is least documented and most often wrong.

EITHER WAY

Forward or reverse

Coordinates are captured travelling in either direction, so the map is built whichever end the access happens to be on.

GIS

In a usable form

Exported into your drawing set or asset system rather than handed over as a picture of a map that somebody has to redraw.

Mapping runs alongside video pipe inspection and feeds NASSCO coding — one mobilization produces the condition record, the measured geometry and the route together.

Find out where the pipe actually goes.

Tell us the access point, the diameter and what the drawings claim. We will tell you whether the route can be mapped on the same visit as the inspection.